Why bobbin thread not catching

The best way of holding the needle is to ensure that it is as tight as possible and sit up correctly. Also, maybe the needle you are trying to grab the bobbin thread with is not the right one for your machine. Or maybe the needle is the right one, but it is bent. In any case, the needle may not be in an excellent position to catch the bobbin thread.

Each machine has a needle that goes well with it. Moreover, the fabric you are sewing requires a specific type of needle. The same applies to the bobbin thread you have, so ensure it suits it.

As you insert the needle into your machine, ensure you are not doing so from the backside of the machine. Ensure that the machine feeds through the fabric to prevent the needle from bending. Another possible cause for the bobbin thread not catching could be that the machine is dirty. Dirt in sewing machines accumulates typically in the area between the fee dogs and the throat plate. It is around this area that the bobbin thread occupies, so the dirt might limit it from catching. It is therefore essential to ensure that you clean this area.

Your sewing machine manual should guide you on how to do this. Ensure you remove all the debris from this area. It would help if you also cleaned below the feed dogs.

Put back the parts that you initially removed and thread the machine again. There is nothing worse than realizing your bobbin thread will catch when you are ready for sewing.

Unfortunately, this issue is pretty standard and has many possible causes, such as it may be your threading which is not okay. Well, no matter the cause, you can quickly fix it by making a few changes here and there in your machine. Here are steps you can follow to solve the bobbin thread not catching.

It is best to solve the issue when your machine is off. So start by doing this. Usually, the bobbin thread rests on the upper side of your machine. So you need to check the state of the upper thread. One of the things you will be checking is such tension. The normal tension of the thread needs to be about 4, and if it is tighter than this, it will not be able to catch. Also, you need to ensure that the threading on this thread is good.

If it is not, you should rethread the machine again. You need to ensure that you are using the correct needle for your sewing machine.

Moreover, the installation of the needle is correct, with the flat side facing towards the back of the machine. Also, the needle does not have any bends. If there is any damage to it, ensure you replace it.

Ensure the bobbin is in the correct position and has an even winding. The bobbin thread should be entirely passed under the pretension so that the winding is even. You should also ensure that it has no scratches and use the right one for your machine.

Finally, if there is any lint, debris, or dust around the bobbin area, clean it up. If you use the correct fabric, needle, and thread, the bobbin thread will not have trouble catching. If you do not feel comfortable constantly changing the bobbin tension for each thread type, you could always have more than one bobbin case that is already adjusted to the kind of thread that you have.

Another potential issue could be dirt and dust collecting inside the shuttle area of your sewing machine. The shuttle area is located under the feed dogs and throat plate in your sewing machine. Not only does cleaning this area out help any potential issues with your bobbin thread, but it is also an excellent habit to get into to preserve the life of your sewing machine.

This can prevent the needle from working correctly because the needle and the hook in the bobbin are not where they need to be at the same time. One way to tell if this is the issue you are having is to check whether or not the hook tip is passing through the loop that is created by the needle. If the needle and its loop do not line up with the hook, located where you would normally place your bobbin, then the stitch can not be completed.

If you are experiencing timing issues, you might need to take your machine in to get looked at by a professional. Retiming your machine yourself can be difficult or even impossible. Threading a sewing machine properly is the first thing that you need to do to make sure that it works properly. You will want to make sure that you wind the bobbin first if you do not already have a bobbin prepared in the thread that you need.

Most sewing machines are threaded similarly, but it can vary from machine to machine. The basics of threading any sewing machine are:. If you have a hard time with threading your sewing machine, most machines have arrows that show you how to thread your machine step by step. Machines also should come with instructions regarding the proper way to thread them, which is great if you are working with a machine that you are not familiar with.

This can cause the tip of the needle to break. The biggest culprit of the needle hitting the bobbin case is if the bobbin case is not placed correctly. If you follow the tips and tricks in this article, however, you should be able to fix most bobbin problems you come across and hopefully, avoid most of those problems altogether.

Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Written By. Last Updated on 7 January, by Sharon. Faulty Bobbin Thread? Try These Tips There are a few aspects of your sewing machine to check on if you notice that your bobbin thread is not being picked up by your sewing machine. The Needle Your bobbin could be malfunctioning due to the needle you are using.

Threading Issues If you have not correctly threaded your machine to begin with, this could lead to problems with the bobbin. Thread Tension When threading the sewing machine , make sure that the thread remains at the proper tension level. Clean the Sewing Machine One issue that is messing with the bobbin thread could be that dirt and debris have collected inside your sewing machine. Timing Problems Your bobbin may not be catching the thread because the timing of your sewing machine could be off.

What Is the Bobbin Thread For? Needle is Hitting the Bobbin Case Another common bobbin problem that many sewers face is when the sewing machine needle actually hits against the bobbin case. Bunching Bottom Thread Bunching thread from the bobbin is another problem that could happen with your sewing machine.

Avoiding Bobbin Issues The best way to deal with bobbin issues is to avoid them altogether in the first place. You should be sure to always turn the handwheel in an anticlockwise motion because turning it the other way could inflict damage on your machine's timing. Be sure that the presser foot is always in the down position before you begin to sew. Trying to sew with the presser foot up with tangle your thread and could even cause your bobbin to jam.

Change your needles often, as dull needles can damage both your machine and your fabric. A good rule of thumb is to change needles after about 16 hours of continuous use. Check to see if you are using the right kind of bobbin for your machine. Some bobbins that look very similar can actually be very different. Using the wrong kind of bobbin for your machine can do damage to it, so be sure to consult your user manual. Happy sewing! Leave a Reply Cancel reply Your email address will not be published.

This fueled my passion for making clothes and soon lead me to creating Top Sewing Machines. A site where I talk sewing machines, overlockers along with tips and tricks and buyers guides. Search for:.